 |
| Home | About Us | Our Products | Contact Us | Enquiry |
|
| Offering you a complete choice of products which include Mass Transfer Lab Equipment such as Adsorption Studies In Packed Bed Column, Sieve Plate Distillation Column, Heat Transfer Through Composite Walls, Vapour-liquid Equilibrium Set- Up and Swenson Walker Crystallizer. |
|
The setup consist of three vertical column packed with activated charcoal (The columns fitted will be different Diameter and packing height to make a comparative study). Columns are operated individually. Liquid feed with dye is Fed to the individual column from the bottom and samples are collected from the top at regular interval of time.
Rotameter is provided to measure the flow rate. Pump with a feed tank is provided for fluid flow.
|
The setup is designed to demonstrate principles of distillation in a Sieve Plate Column.
The column is made of Stainless Steel material with seven sieve trays. An electrically heated re-boiler is installed at the bottom of the column. The bottom product is collected in the tank. The vapors form the top of column are condensed in the shell and tube type condenser by circulating cooling water supplied by laboratory overhead tank. The condensate is divided into reflux & distillate and R/D Ratio can be varied. Reflux is fed back to the column and distillate is received in a receiving tank. The complete column is insulated for minimizing the heat loss. Instrumentation is done for pressure & temp. Measurement wherever is necessary.
Rotameter is provided to measure the flow rate. Pump with a feed tank is provided for fluid flow.
|
|
|
The setup consists of a heater sandwiched between two sets of slabs. Three types of slabs are provided on either sides of heater, which forms a composite structure. A small hand press frame is provided to ensure the perfect contact between the slabs. A variac is provided for varying the input to the heater and digital voltmeter and digital ammeter display the heat input. Heat produced by heater flows axially on both the sides. Temperature sensors are embedded between interfaces of slabs to determine the temperature gradient. The experiment can be conducted at various values of input and calculation can be made accordingly. |
The set-up is designed to demonstrate and study the vapor-liquid equilibrium. As basic data of any distillation problem is the equilibrium between the liquid and vapor phases of the system subjected to distillation. Hence it is of great importance to study the VLE. The set-up consists of distillation still with a heating element, shell & tube condenser, reflux & distillate section. A tank with pump is provided to circulate cold water to condenser. Flow rates can be regulated through control valve fitted. Instrumentation is done to measure the temperatures at different points. A Digital Temp. Controller is connected to heating element for precisely controlling & varying heat input. The vapors form the top of column are condensed in the shell and tube type condenser by circulating cooling water. The condensate is collected in reflux drum and feedback to column as reflux. |
|
|
The set-up is designed to demonstrate and stimulate the phenomena of crystallization. Swenson Walker crystallizer is a continuous type crystallizer. This operation involves both heat and mass transfer. Crystallization is the formation of solid particles within a homogeneous phase. Its wide use has a two-fold basis; a crystal formed from an impure solution is itself pure.
The setup consists of a top open jacketed round bottom trough. A ribbon mixer is provided in crystallizer trough, which rotates at low rpm for agitation of saturated solution. The saturated solution is prepared in a tank fitted with heater and a stirrer. This hot saturated solution is fed at one end of the crystallizer and flows slowly towards the other end while being cooled and is allowed to flow back in hot feed tank making the process continuous. The crystals sediments at the bottom of the trough, and can be washed out at the end of process. Arrangement for Cooling water circulation and flow measurement in jacket is made by using storage type water tank, a pump and a rotameter. Necessary instrumentation is done for temp measurement.
|
Mr. Varun Chopra
(CEO)
Edutek House, 29- B, Inderpuri, Ambala Cantt
Ambala,
Haryana -
133 001,
India
Telephone: +(91)-(171)-2654329
© Edutek Instrumentation. All Rights Reserved (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited
|
Business Enquiry Form |
