Clean Air Systems

Product Details:

Fume Hoods ETC-72

Designed to contain and exhaust toxic, obnoxious, pungent smelling gasses to protect personnel and equipment in the laboratories. The fume hood comprise with international standard on fume handling systems. A motor driven dynamically balanced blower with minimal vibration and noise level creates negative pressure and sucks contaminated air from work area and throws the same in high-up atmosphere through ductings.

Fabricated out of thick Duro-board clad from outside in laminated sheet and inside finished in non-corrosive, chemical resistant Epoxy paint. An up & down sliding Sash made of Teakwood mounted in thick glass sheet and workable on weights & pulleys system counter balanced is provided. Fluorescent lighting is provided in the chamber. A gas tap and electric power plug also provided in addition to stainless steel wash basin and suitable water tap.

A work-bench with cupboard is provided to hold the hood at suitable level from ground :

• Chamber : 3x2x2
• Chamber : 4x2x2'
• Chamber : 6x2x2'
• Chamber : 8x3x3'

Additional Information:

• Item Code: ETC-72

Product Details:

Laminar Air Flow Cabinets ETC-73A

Laminar Air Flow Cabinets works on laminar flow principle involves double filtration of air through coarse Pre Filters (upto 5 microns) and Hepa filters (down to 0.3 microns) for filtration of Biological & Particulate contaminants. A constant uni-directional air flows either Horizontally or Vertically, is drawn from atmosphere and passed through pre and Hepa filters on to the work surface. Fabricated out of reinforced pest and weather resistant Duro-board which is clad in from outside in laminated sheet and inner exposed areas are finished in Epoxy paint. Table top stainless steel sheet. Side panels are fixed and made of clear plexiglass. Front door is folding & made of clear plexiglass.

Prefilters:-

DOP tested as per Standard BS: 2831 with efficiency 90% down to 5microns. Made of Washable synthetic material.

Hepa Filters:-

Made of Microglass fibre with corrugated aluminium foil separators. DOP tested as per US Standard 209B. Efficiency 99.97% down to0.3 microns.

Blower Units:-

Assembly of AU or equivalent motor workable on 220V AC 50Hzsingle phase, dynamically balanced blowers making the unit least vibrant with minimum noise level.

Features:-

• Lighting : Fluorescent tube lights
• Sterilization : Germicidal Ultra Violet (UV) tube
• Manometer : Static pressure thick Acrylic block type

K-System:-

The K-System encompasses the specialist requirement of ocyte, and embryo handling during procedures in both animal and human reproduction. The K-system is often built into a Laminar Flow Cabinet. The utensils are warmed by the heating of part of the table plate of the cabinet.

The transmitted light source and the regulation transformer for the stereo microscope are located under the stainless steel table plate, with a window for transmitted light built into the table plate.

Advantages of the K-System:-

• Maximum working area in Laminar Flow Cabinet
• Handling of ocytes and embryos on one level
• All ocytes from one patient in one storage tray
• Ocytes stored in cabinet until insemination
• Cleaning is easy and sterilization possible
• Laminar with All Stainless steel body / Sealing / Wall Hanging can also be fabricated
• Suitable for Pharmaceutical Industries as per the requirement

Available in following sizes :-

• Working Chamber: 2 x 2 x 2'
• Working Chamber: 3 x 2 x 2'
• Working Chamber: 4 x 2 x 2'
• Working Chamber: 6 x 2 x 2'
• Working Chamber: 8 x 2 x 2’

ALSO AVAILABLE IN MILD STEEL/STAINLESS STEEL BODY

Additional Information:

• Item Code: ETC-73A

Product Details:

Laminar Air Flow Cabinet ( Stainless Steel) ETC-73C

• Table Top model.
• Satin Finish S.S.Table Top(in lieu of formica Top).
• Traansparent front door.
• Static Pressure. Inclined Manometer.
• Built in U.V.Germicidal light.
• Cock for gas, air or vacuum line.
• Cold rolled MS Sheet body duly powder coated.
• Stainless steel body duly polished.
• Particle dust count validation at site after installation.
• HEPA Filter.
• Pre Filter.

Available in following sizes :-

• Working Chamber: 2 x 2 x 2'
• Working Chamber: 3 x 2 x 2'
• Working Chamber: 4 x 2 x 2'
• Working Chamber: 6 x 2 x 2'
• Working Chamber: 8 x 2 x 2’

Additional Information:

• Item Code: ETC-73C

Product Details:

Tissue Culture Hood  ETC-75

Tissue Culture Hood/Aseptic Cabinet is an elegant equipment with overall dimensions 1220 x 610 x 610 mm having front horizontal swing door opening of 1050 x 405 mm (frame) fitted with transparent plexiglass. Complete with fluorescent lighting and germicidal ultra violet tube.

Additional Information:

• Item Code: ETC-75

Inoculation Hood ETC-75A
Inoculation Hood is fabricated out of pest and weather resistant Duro-board or mild steel sheet. Wood construction clad in laminated sheet from outside and inner exposed parts painted with Epoxy paint. The mild steel model is enamel painted.

Provided with rectangular, tight covered opening on one side for putting the material in the chamber and two covered round openings in front for handling of the material. A clear Acrylic fixed window in front provided for observation. Complete with fluorescent lighting and germicidal Ultra Violet (UV) tube.

Chamber Sizes:-

• 40' x 24' x 20'
• 27' x 20' x16'

Additional Information:

• Item Code: ETC-75A

Product Details:

Laminar Air Flow Cabinet ETC-73B

• Micro-Controller based : Menu Controlled with LCD Display. Refer first page for Menu functions.
• Operation Laminar Airflow Velocity : Average of 0.45 m/s or 90 fpm measured 150mm/6” filter face for 45 air changes/min. in work zone.
• Re-circulation : 70% of total.
• Air Velocity Exhaust : 30% of total Air Velocity.
• Air Cleanliness in Working Area : meets or exceeds US Federal Standard 209E Class 100.
• Main & Exhaust Filters : HEPA (Minipleat Optional).
• HEPA Filters : Rated for min. 99.97% efficiency at 0.3 micron particle size.
• Pre-Filters : Low pressure drop. High efficiency, 10 microns.
• UV Sterilization : In work chamber & Exhaust Plenum. Emission in the germicidal band UV-Cm 254mm.
• Alarm : Door unsafe position.
• Noise Level : <58 dbA at operator point.
• Power : 220-240V AC / 50 Hz 1 Ph.
• Inter Lock : UV / Fluorescent / Door.
• Exhaust : Double protection with HEPA & UV.
• Motors / Blowers : Double shaft, Balanced, low vibration.

Additional Information:

• Item Code: ETC-73B

Multiplate Clutch

A properly constructed all metallic model mounted on metal base with handle drive arrangement.

Additional Information:

• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer)

Product Details:

Laminar Air Flow Cabinet ETC-73

works on laminar flow principle involves double filtration of air through coarse Pre Filters (upto 5 microns) and Hepa filters (down to 0.3 microns) for filtration of Biological & Particulate contaminants. A constant uni-directional air flows either Horizontally or Vertically, is drawn from atmosphere and passed through pre and Hepa filters on to the work surface. Fabricated out of reinforced pest and weather resistant Duro-board which is clad in from outside in laminated sheet and inner exposed areas are finished in Epoxy paint. Table top stainless steel sheet. Side panels are fixed and made of clear plexiglass. Front door is folding & made of clear plexiglass.

Prefilters:-

DOP tested as per Standard BS

2831 with efficiency 90% down to 5

microns. Made of Washable synthetic material.

Hepa Filters:-

Made of Microglass fibre with corrugated aluminium foil separators. DOP tested as per US Standard 209B. Efficiency99.97% down to 0.3 microns.

Blower Units:-

Assembly of AU or equivalent motor workable on 220V AC 50Hzsingle phase, dynamically balanced blowers making the unit least vibrant with minimum noise level.

Features:-
 

• Lighting : Fluorescent tube lights
• Sterilization : Germicidal Ultra Violet (UV) tube
• Manometer : Static pressure thick Acrylic block type

Sizes are Available: 

• Working Chamber: 2 x 2 x 2'
• Working Chamber: 3 x 2 x 2'
• Working Chamber: 4 x 2 x 2'
• Working Chamber: 6 x 2 x 2'
• Working Chamber: 8 x 2 x 2’

 
ALSO AVAILABLE IN MILD STEEL/ STAINLESS STEEL
BODYK-System:-

The K-System encompasses the specialist requirement of ocyte, and embryo handling during procedures in both animal and human reproduction. The K-system is often built into a Laminar Flow Cabinet. The utensils are warmed by the heating of part of the table plate of the cabinet.

The transmitted light source and the regulation transformer for the stereo microscope are located under the stainless steel table plate, with a window for transmitted light built into the table plate.

Advantages of the K-System:-

• Maximum working area in Laminar Flow Cabinet
• Handling of ocytes and embryos on one level
• All ocytes from one patient in one storage tray
• Ocytes stored in cabinet until insemination
• Cleaning is easy and sterilization possible
• Laminar with All Stainless steel body / Sealing / Wall Hanging can also be fabricated
• Suitable for Pharmaceutical Industries as per the requirement

Additional Information:

• Item Code: ETC-73

Product Details:

Bio Safe Biological Safety Cabinet ETC-74

These Class I safety cabinet provide protection for the operator and the environment, with inward airflow away from the operator. Air is filtered before release to the atmosphere.

Negative pressure is maintained within the cabinet, which is suitable for work where no product protection is required.
These cabinets are self contained 100% exhaust containment enclosures. Air from the work zone passes through a two-stage, high efficiency filter system before being exhausted to the room/atmosphere. These cabinets may be installed on standard laboratory benches or on optional support stands.

Personnel and environment protection is provided by inward flow of room air at the work area and high-efficiency particulate air (HEPA) filtration of exhaust air. The inward airflow sweeps aerosols generated during the work process away from the operator into the filter system. A pre-filter protects the HEPA filter from large particles, and the HEPA filter removes particulate contaminates down to sub-micron size from the exhaust air.
Supplied complete as above, with cord and plug, suitable to work on 220V single phase, 50Hz, AC supply.

Available in following sizes :-
Work area: 

• 3' x 2' x 2'
• 4' x 2' x 2' , 
• 6' x 2' x 2'

Additional Information:

• Item Code: ETC-74

Portable Tissue Culture Rack ETC-77

A high quality of tissue culture rack with following features:

• Fabricated out of aluminium square pipe or angle fitted with sturdy castor wheel for smooth shifting movement of the unit.
• Shelves are made of wooden with aluimnium clad or frosted glass.
• Each shelves has been provided with four fluorescent tubes of 4’ size.
• The unit is workable on 220V AC 50Hz single face.
• Heavy duty electronic chokes have been mounted separately on each shelf.
• Photoperiodic timer.

Available shelves:-

• 4 shelves
• 5 shelves
• 6 shelves.

Additional Information:

• Item Code: ETC-77

Dehumidifier ETC-76

Dehumidifiers are designed to remove excess moisture from atmosphere when manufacturing activities of tablets, capsules and air accuracy is required. Humidity can be brought down to 30% RH with accuracy of ±3% RH.

Capacity:-

• 1 Ton
• 1.5 Ton
• 2 Ton
• 3 Ton.

Additional Information:

• Item Code: ETC-76