Engineering Training Equipment

Product Details:

The unit consists of an inclinable channel mounted on a frame, together with a discharge tank and recirculating pump. To commence a demonstration, sand is placed evenly along the channel bed, between the inlet tank and the overfall discharge weir. Water is circulated around the system at one of the three selectable flow rates. The channel slope is adjusted by means of a fine screw jack to which an accurate slope indicator is attached. The channel sides are transparent in order that bed profile changes can be observed, and a section of one side is provided with graphical grid markings to permit quantitative assessments to be made of bedform dynamics.

Product Details:

Item code: 11978

We are manufacturers of finest Modular Power Hub in India and also supplies and exporters Modular Power Hubaround the world at best prices. To enquiry Modular Power Hub , please fill below form. We'll be back with you

Feature :

• DC power cord application eliminates the use of the extension cord keeping your server room neat
• Front panel LEDs indicate the real-time power consumtion
• Fool-Proof plugs, avoid short-circuitry
• Provide 8 extra power source for the connected devices
• 4 DC receptacles on the front panel plus 4 DC receptacles on the rear panel make connections easy to reach

 

Additional Information:

• Item Code: 11978

Product Details:

Item code: 11973

This apparatus is used to determine the air pressure differential across the column as a function of air flow rate at different water flow rates down the column, and flooding point can be noted. Absorption process of carbon dioxide from air-CO2 mixture into caustic soda solution, is also studied using this system.

The system components are mounted within a floor standing painted steel framework.

The wetted wall column is a glass column with water inlet and outlet sections and is gimbal mounted to ensure that it can be set accurately vertical.

The deoxygenating column is of similar overall size to the wetted wall column, standing vertically adjacent to it. Beside the columns is a control console housing flow meters, pump controls and oxygen analyser. Situated between the columns are two special housings containing the oxygen analysis probes which monitor the oxygen content in the water entering and leaving the absorption column. The apparatus uses water as the working medium, contained in a storage tank at the rear of the unit. Pumps delivering water to the deoxygenator and the absorption column are located at the base of the unit.

Dissolved oxygen at inlet and outlet can be measured in rapid succession. The water drains into the storage tank to be recycled to the deoxygenator.

In operation, water is sparged with nitrogen in the deoxygenator before entering the top of the wetted wall column. Air is pumped by the integral diaphragm type air pump into the base of the column. The air passes up the column, giving up the oxygen to the water.

 

Additional Information:

• Item Code: 11973

Product Details:

Item code: 11962

Edutek  evaporator processes samples in smallest volume under production conditions, sufficient to reveal the effect of heating on any ingredients.

Having single tube-in-jacket evaporator.with longer tubes within the steam space. feed tank, vapour/liquid separator, condenser, concentrate tank, condensate tank, CIP pump and vacuum pump, all manufactured from stainless steel, PTFE and glass.

A sturdy framework and requires only connection to suitable steam, electrical and water services for operation.

 

Less floor space is required to install the evaporator and can to fit easily into a room of standard height.

 

Additional Information:

• Item Code: 11962

Product Details:

Item code: 11964

Our expertise in the field of manufacturing has helped us satisfy the expectations of our clients. The Sedimentation Studies are high quality equipments which are manufactured at our ultramodern infrastructure facility in compliance with the prevailing industrial standards. These are supplied to clients in different specifications at affordable market prices. Known for their sturdy designs and durable exterior, these equipments are highly demanded by chemical engineering laboratories.

Additional Information:

• Item Code: 11964
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Item code: 11994

High temperature gas-cooled reactors use helium as coolant, ceramics as coating for fuel particles, and graphite as reactor core structural materials. The HTGR is recognized worldwide as an inherently safe reactor.
¡¡Coated particles are used as its fuel. The particles are black, spherical and less than 1 mm in diameter. The fuel kernel of the particles is made of uranium oxide or carbide and coated by four thin layers of special carbon and silicon carbide ceramic to protect the kernel and prevent it from releasing products generated by nuclear fission. Kernals coated with carbon and silicon carbide have greater heart-resistance than those coated with metallic materials, and do not melt down even at temperatures above 1,000.
¡¡Helium is used to cool the reactor core, which reaches about 1,000 with the heat transferred to the helium. The heated helium is removed from the reactor after circulating in the core and used for various experiments. Being chemically insert, helium cannot react with fuel and structural materials, which makes it extremely safe at high temperatures and the best coolant to remove the dense heat flux.
¡¡As structural material in the core, graphite has excellent properties such as low neutron absorption, minimal radiation damage, superb heat resistance and high thermal conductivity. This graphite function to protect the fuel and maintain fission reaction by moderating the speed of neutrons generated.

Additional Information:

• Item Code: 11994

Product Details:

Item code: 11984

Pressure Measurement Trainer comprises of strain gauge based pressure cell, foot pump to build the pressure, pressure tank fitted with release valves and a bourdon pressure gauge. Digital pressure indicator to read the pressure in Kg / Cm² is provided.

Pressure Sensor : Strain gauge based,
capacity 10 Kg/cm²Indicator : 3½ digit to read upto ±1999 counts.
Bridge Balancing : Potentiometer Bridge
Excitation : 10V DC
Resolution : 0.1 Kg/cm²
Power Supply : 230V ±10%@50Hz Accessories Pressure chamber with Dial gauge, Foot air pump.

Additional Information:

• Item Code: 11984

Product Details:

Item code: 11960

Edutek RO/UF unit is the smallest known industrial membrane system of its type in the world. It is designed specifically for laboratory scale testing of both reverse osmosis and ultrafiltration techniques.

The 11960 is fully self-contained in a mobile cabinet. Comprehensive instrumentation is provided with digital meters displaying temperatures and system pressure. In addition to the membrane module, the cabinet also houses feed and permeate tanks, a plate heat exchanger and positive displacement pumps. Connection to cooling water and a suitable electrical supply is all that is required for normal operation.

All parts in contact with the process fluid are constructed from hygienic design materials such as stainless steel, PTFE and silicone rubber.

The RO/UF unit has an efficient clean-in-place facility and is easily dismantled for servicing or maintenance.

Membranes can be installed or removed rapidly for use in either process.

The filtration membranes differ only in length and quantity from those installed in the full-scale plant. Using small quantities of process fluid, operating parameters can be established and then optimised to effect a confident transition to full-scale.

Additional Information:

• Item Code: 11960

Product Details:

Item code: 11968

• The Machine is tabletop and compact.
• A single operation unit designed for coating of photo resist laminate on copper clad.
• The machine ensure uniform controlled thickness of Photo resist on copper clad.
• Maximum Board size : 250mm x 300mm (10" x 12").
• Tank Capacity : 2 liters.
• Dips one PCB at a time.
• Motorized lead screw system.
• Micro switch to prevent motor from getting damage.
• Electrical power : 230V/50Hz, 5ASocket required.

Additional Information:

• Item Code: 11968

Product Details:

Rapid Extractor
Item code: 11958

Laboratory Scale Rapid Extractor is used to extract the active constituents from materials in laboratory scale batch sizes.
The Edutek 11958 uses high pressure and extraction phases to achieve a rapid extraction of the active materials with minimum degradation to the product

Additional Information:

• Item Code: 11958

Product Details:

Item code: 11965

We are manufacturers of finest Computerized Flow Meter Calibration Equipment in India and also supplies and exporters Computerized Flow Meter Calibration Equipment around the world at best prices. To enquire Computerized Flow Meter Calibration Equipment , please fill below form . We'll be back with you.

• Cost-effective and simple to use.
• Unique ‘quick-change’ flow meter adaptors and pressure connections.
• Multi-tube manometer to show flow meter and overall pressure changes.
• Optional flow meters for comparison: Venturi, orifice, nozzle and Pitot tube.
• Shows the boundary layer effect and the fluid velocity profile – needs Pitot tube .
• Includes hand-pump and manifold with air valve for increased measurement range.
• Works with Gravimetric or Volumetric Hydraulic Benches for easy installation.

Description
The Flow Meter Calibration apparatus is for use by all kinds of engineering students. It compares and shows the accuracy and use of the optional fundamental flow meters. Any of the optional flow meters quickly and easily fit into place between the adaptors in the base unit of theapparatus. Four water-filled manometers show the pressure differences at the flow meter and across the overall flow meter assembly. The manometers have a common manifold fitted with an air valve. Students use the handpump (included) to increase the air pressure in the manifold. This ‘offsets’ the manometer measurement (adjusts the datum).The straight pipe (included) gives a comparison of the true pressure losses caused by the flow meters.The optional Pitot Tube Flow Meter will also show the velocity profile in a pipe. This helps to explain the ‘boundary layer’ and surface friction in pipes and flow channels.Note: You must order at least one of the optional flow meters to use with the Flow Meter Calibration apparatus.

Standard Features :

• Supplied with a comprehensive user guide.

Additional Information:

• Item Code: 11965A
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

We are a respectable name engaged in manufacturing and exporting a vast range of precisely engineered laboratory glassware, chemistry laboratory equipment and scientific instruments. These products are fabricated using light weight and resilient raw material such as borosilicate and quality plastic procured from trusted vendors after stringent pre-checks. We design and machine our lab instruments using technologically superior machinery in tandem international quality standards. Our entire product range is available in standard as well as customized specifications at best market prices.     We are one of the well known exporter of Lab Glassware & Scientific Instruments from India. We are looking for Foreign Buyers for our products.

Product Details:

Universal Coupling Model

Model No: ETK-9025

Edutek are leading manufacturer and exporter of all type Engineering Models and Mechanism Models For Educational and training.

• Properly constructed all metallic model.

Shafting General Bearing

Model No:  ETK-9011

Properly constructed section cut wooden models.

a) Open Truck Bearing.
b) Simple bearing.
c) Bush Bearing
d) Thrust Bearing
e) Plummer Block of pedestal Bearing
f) Foot Step Bearing

Additional Information:

• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer)

Product Details:

Internally Expanding Brake  

Model No:  ETK-9007

The model consists of a hollow drum, two shoes are pivoted pins. Braking action can be seen due to application of the force on the cantiever.

Additional Information:

• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer)

We are manufacturer and exporter of all type engineering teaching equipment.

Product Details:

Specification :

• 1 off 22.5mm ID
• 2off 17.5mm ID
• 2 off 13.0mm ID
• common length 0.7m. Circulating pump: 0.55kW (0.75 HP) centrifugal.

Differential pressure measurements:

• 1m pressurized water manometer;
• 1m mercury manometer .
• Volumetric flow measurement range: 0-6 liters and 0-40 liters with level indication on remote sight gauge

Additional Information:

• Delivery Time: 1 Week
• Packaging Details: Box , Carton

Product Details:

Item code: ETE-2114

This equipment is designed for carrying out the experiment for balancing a rotation mass system. The apparatus consists of a steel shaft fixed in a rectangular frame. A set of four blocks with a clamping arrangement is provided. For static balancing, each block is individually clamped on shaft and its relative weight is found out using cord and container system in terms of number of steel balls. For dynamic balancing, a moment polygon is drawn using relative weights and angular and axial position of blocks is determined. The block are clamped on shaft is rotated by a motor to check dynamic balance of the system. The system is provided with angular and longitudinal scales and is suspended with chains for dynamic balancing.

Experiment :

• To balance the masses statically and dynamically of a single rotating mass system.
• To observation of effect of unbalance in a rotating mass system.

Utilities Required :

• Electricity 0.5kW, 220V, Single Phase.

Additional Information:

• Item Code: ETE-2114

Product Details:

Pore Pressure Apparatus
Item code: ESTE-124

Same as above, but fitted with pressure gauge 0-20 kg/cm2 x 0.2 kg/cm².Spares: Polythene tube 3 mm bore x 5 mm O.D.

Additional Information:

• Item Code: ESTE-124

Steam Engine Model with a Boiler  11995

Operation of a commercial steam engine is well illustrated with this working model. The extra large size unit Is provided with a horizontal boiler with a whistle, safety valve, steam gauge, heating lamp and a small dynamo model.

Train Of Gear Wheels

An economical model to determine the velocity ratio complete on stand.

(A) Simple
(B) Compound

Product Details:

Single Shoe Brake

The model consists of a brake drum, mounted on a shaft free to rotate in bearings, provided with brake lever, complete on cast iron machined base.

Additional Information:

• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer)
• Delivery Time: 3 Days
• Packaging Details: Box Carton

Product Details:

Item code: 11975

Edutek - Instrumentation, Suppliers and Exporters Engineering Instruments and Equipments which are Best used for Educational purposes in Engineering Colleges. Manufactured using superior quality raw material, this machine is useful for making the roughage and rava of daliya, idli rava, sogi kesari rava and maize.

Additional Information:

• Item Code: 11975

Product Details:

Composite Wall Apparatus

Item code: ET-11935

• To determine total thermal resistance & thermal conductivity of composite wall.
• To plot temperature gradient along composite wall structure.
• The experiments can be conducted at various values of input & calculation can be made accordingly.
• To plot Heat flux Vs thermal conductivity in composite structure.

EXPERIMENTAL SETUP :

1. Heater Assembly.

2. Test specimen MS 2 Nos. Bakelite 2 Nos. Wood 2 Nos.

3. Assembly Mounting frame.

4. Clamp Plates 2 Nos.

5. Set of thermocouples.

CONTROL PANEL :

• 12 Channel Digital Temperature Indicator.

• Dimmerstat : 0 - 2 A.
• Main's On/Off Switch.
• Voltmeter : 0 - 250 V.
• Ammeter : 0 - 3 A.

 

SPACE REQUIRED :

• 1.5 m.(L)x 1.0 m(W) table top.

 

Service Required :

• 230 v Ac Supply 50 Hz.

Additional Information:

• Item Code: ET-11935

Product Details:

Item code: ET-11987

This Unsteady State Heat Transfer Unit has been designed to allow students to run experiments on unsteady state heat transfer. The unit is supplied with a heated water bath and a set of solid shapes with built-in temperature sensor to monitor the temperature at the center of the shape. Monitoring of the temperature at the centre of the shape allows analysis of heat flow using the appropriate transient-temperature/heat flow charts provided.

Unsteady State Of Heat Transfer :

• To determine film heat transfer coefficient between the medium in which body is heated.
• To determine film heat transfer coefficient between the medium in which body is cooled.

EXPERIMENTAL SETUP :

1.Heater Assembly.
2.Aluminum Test Cylinder.
3..Fully insulated hot bath assembly.
4.Set of thermocouples.

CONTROL PANEL :

1. 12 Channel Digital Temperature Indicator.
2. Main's On/Off Switch.
3. Voltmeter :0 - 250 V.
4. Ammeter :0 - 15 A.

SPACE REQUIRED :

• 1.5 m.(L)x 1.0 m(W) table top.
• 230 v Ac Supply 50 Hz.

Additional Information:

• Item Code: ET-11987

Product Details:

Item code: 11977

The Basic Hydraulic Bench is of volumetric type and has been designed to provide continuous and controlled supply of water to conduct various experiments using auxiliary modules in typical Fluid Mechanics and Hydraulics Laboratory. The unit is an ideal service unit for conducting student projects. Once filled, no external water supply is required. Water is recycled between the Experiment Module, Measuring Tank and the Storage Tank by the Centrifugal Pump.

Several experiments in Fluid Mechanics and Hydraulics require continuous and controlled supply of water. The Basic Hydraulic Bench provides a controlled recirculation water supply to conduct experiments.

The Basic Hydraulic Bench is a very important module and is recommended for all Fluid Mechanics and Hydraulics Laboratories in Educational Institutions. It is a basic module for flow related experiments using auxiliary modules.
A list of common experiments that can be conducted using the Basic Hydraulic Bench is given below:

1. Impact of a Jet
2. Flow over Weirs
3. Bernoulli’s Theorem Demonstration
4. Orifice Discharge
5. Energy Loss in Bends
6. Osborne Reynolds Demonstration
7. Energy Loss in Pipes
8. Hydrostatic Pressure
9. Flow Visualization in Channels
10. Dead Weight Calibrator
11. Metacentric Height
12. Series & Parallel Pumps
13. Centrifugal Pump Characteristics
14. Free and Forced Vortices
15. Water Hammer
16. Pelton Turbine
17. Orifice & Free Jet Flow
18. Flow Meter Demonstration
19. Cavitations Phenomenon Demonstration
20. Laminar Flow Demonstration
21. Radial Flow Turbine
22. Venturi, Bernouli and Cavitation
23. Pipe Friction Apparatus
24. Equipment for the Study of Porous Beds in Venturi Tubes
25. Flow Channel 1m Length
26. Depression Measurement System (Vacuum Gauge)
27. Axial Flow Turbine
28. Pump Impeller Display Panel

Features

1. Self contained and fully portable mobile unit with welded frame.
2. Light weight body made of reinforced fiber glass and corrosion resistant materials.
3. Closed water circuit consisting of Measuring Tank, Storage Tank and the Centrifugal Pump.
4. Control valve to regulate the pump and adjust the flow rate.
5. Work space on Bench Top has integrated flow channel for flow measurements using
Weirs and is fitted with stepped edge to ensure safe and easy mounting of experiment modules.
6. Suitable pipe connectors are provided in the Bench Top to enable easy change of experiment modules.
7. Graduated and stepped Measuring Tank for both low and high volume flow rates.
8. Level Indicators for water level are provided in the Open Channel and Measuring Tank.
9. Variable area Flow Meter (10-75 liters per minute) is also provided to measure flow rate independently.
10. Stilling baffles are provided to reduce turbulence.
11. Sight tube with scale provided to indicate instantaneous water level.
12. Bull’s eye level is provided to ensure proper position of the Bench and accurate reading of levels.
13. Remote Actuator provided to operate the Dump Valve at the base of Measuring Tank
14. Over Flow provided in Measuring Tank to avoid flooding.
15. Separate Storage Tank Outlet facility provided to enable the Bench to be used in any hydraulic circuit.
16. Push button starter provided for the centrifugal pump.
17. Power supply includes over-load and under-voltage protection.

Additional Information:

• Item Code: 11977
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer)
• Production Capacity: Ready Stock

Product Details:

Item code: 11972

• A space-saving vertical panel that works with Gravimetric or Volumetric Hydraulic Benches for easy installation.
• Includes different valves, pipes and fittings to show losses.
• Includes experiments on roughened pipes.
• Shows laminar and turbulent flow.
• Uses Bernoulli’s equation.
• Shows how to use Venturi and orifice meters to measure flow.
• Includes a traversing Pitot tube to measure velocity profile

Fluid Friction Apparatus allows students to study flow, flow measurement techniques and losses in a wide variety of pipes and fittings. The equipment has three water circuits with instruments,pipes and pipe system components. These allow students to examine and compare the different component characteristics. A hydraulic bench (Gravimetric ) or Volumetric , available separately) supplies the circuit with a controlled flow of water. A space-saving vertical panel holds all the parts for easy use. To measure pressure loss across components, students use a piezometer set and differential pressure gauge (included). To perform experiments students record the temperature of water in the hydraulic bench and set the hydraulic bench to pump water through a circuit. They measure pressure losses across instruments or components. The hydraulic bench gives an external flow rate for reference and comparison. The flow measurement instruments show students the common methods of measuring water flow. They also give applications of the steady flow energy equation (Bernoulli’s equation). Students use a Venturi meter and an orifice plate meter and compare the losses of each. They also find the losses in a rapid enlargement.

The equipment also includes a Pitot-static tube. By traversing the Pitot across the pipe diameter, students can find the velocity profile and flow coefficients. They also find the relationship between the flow rate and pressure differential.An artificially roughened pipe allows students to study friction factor at different Reynolds numbers, covering the interesting transitional flow from laminar to turbulent.They can compare results to those predicted by Nickuradse’s results and a Moody chart.

Standard Features :
• Supplied with a comprehensive user guide.
• Two-year warranty.
• Manufactured in accordance with the latest Indian Union directives.

Additional Information:

• Item Code: 11972

Product Details:

Item code: 11991

An educational Venturi tube that allows students to study the Venturi meter and Bernoulli's Theorem and to make direct comparisons between the results obtained by experimentation and those predicted by theory.

A Venturi meter is used to determine the flow rate of fluid in a pipe. Venturi Meter is comprised of a horizontal Venturi tube, a downstream flow-control valve and eleven pressure tappings connected to water manometers (piezometers). A common manifold above the piezometers includes an air pressure control valve.

The inclusion of eleven piezometers allows study of the pressure distribution along the convergent-divergent passage within the Venture tube.

Additional Information:

• Item Code: 11991

Product Details:

CNC Milling Machine ETK-8001

We are manufacturer and exporter of CNC Milling machine .

Features of CNC Milling Machine

Brushless Motor 1kWScrap Collection DeviceSpindle Motor Speed Max. 5000rpmContain Fourth Axes Connection Socket

Specifications of CNC Milling Machine

Drilling Capacity: 16mm (0.6”)Worktable Size: 500x160mm (22” x 6.3”)Worktable T-Slot Size: 12mm (0.5”)Max. Loading of Worktable: 35 kgTable Travel x axes: 280mm (11”)Table Travel y axes: 120mm (4.7”)Table Travel z axes: 270mm (11”)X Axes Feeding Motor Power: 4NmY Axes Feeding Motor Power: 4NmZ Axes Feeding Motor Power: 6NmX/ Y/ Z Axes Max. Moving Speed: 2m/minX/ Y/ Z Axes Feeding Speed: 500mm/minThroat: 232mm (5.9”)Position Precision: 0.015mmRepeat Positioning Precision: 001mmSpindle Taper: MT3#/R8/ISO30Spindle Speed: 100-5000rpmSpindle Motor: 1kwMachine Size (LxWxH): 1280x895x1845mmPacking Size (LxWxH): 1420x1060x2035mmG.W./N.W.: 570/510 kg

Additional Information:

• Item Code: ETK-8001
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer)

Product Details:

Item code: 11961

We offer process equipment such as ribbon blender, double cone blender, reaction vessel, universal centrifuge, heat exchanger and condenser, ball mill, industrial tray dryer, high speed stirrer mixer, high speed disperser.

Ribbon blenders are widely used for homogeneous mixing of dry granules & powders. The blender comprises a 'U' shaft with two sets of spiral ribbons, one inside the other. Inner and outer ribbons are perfectly arranged, that during rotation, the material reaches each corner of the trough and imparts radial & linear motion to the whole of the material to be mixed. Our range of ribbon blenders are based on a proven agitator construction that provides a triple mixing action ensuring fast, efficient blending.

Operations:

 
• The complete assembly is mounted on a MS/ SS structure
• The material is moved from side of the trough to the center and vice versa resulting in quick & homogeneous mixing
• Double ribbon configuration also brings material towards central bottom outlet while discharging
• A specially designed valve is provided at the center or butterfly valve for discharge
• Blending is achieved in semi-fluidized state in the upper zone of the trough when used for fine powders
• Machine can be provided with spray nozzles with pressure spraying system for spraying additives in blenders
• Ribbon blender can also be used as dryer by providing jacket on the trough

 

Additional Information:

• Item Code: 11961
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Item code: 11971

• Shows flow and losses in different pipes, fittings and valves. Shows popular flow measurement instruments.
• A space-saving vertical panel that works with Gravimetric or Volumetric HydraulicBenches for easy installation.
• Includes different valves, pipes and fittings to show losses.
• Includes experiments on roughened pipes.
• Shows laminar and turbulent flow.
• Uses Bernoulli’s equation .
• Shows how to use Venturi and orifice meters to measure flow.
• Includes a traversing Pitot tube to measure velocity profile.

Additional Information:

• Item Code: 11971

Product Details:

Hydraulic Bench Computerised 11913

Technical Specification OF Hydraulic Bench Computerized:

Same as above Basic Hydraulic Bench But Controlled with Computer Interface On & Off (Voltage , Temperature, Flow Rate, and Pressure)

Additional Information:

• Item Code: 11913
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer)
• Production Capacity: Ready Stock