Fluid Mechanics & Hydraulic Lab Equipments

Product Details:

Flow Meter Demonstration

Model No : ET-245FM

Edutek Instrumentation are offering a wide reange of Flow Meter Demonstration Unit.This experiment has been done to measure the flow rate and associated pressure losses with three devices which is venturi meter, orifice meter and variable area meter. First of all, we must close the ball valve and measure the time taken to accumulate a known volume of fluid in the tank, as measure from the sight-glass. Then, we record all the manometer height and the variable area meter reading and carry out a timed volume collection using the volumetric tank.

OBJECTIVE :

To investigate and contrast the operation and characteristics of three different basics types of flow meter which venture, variable, and orifice including accuracy and energy losses.To measure a pressure drop at different segment of device.To determine a flow rate through a pipe.

Additional Information:

• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer)

Product Details:

Impact Of A Jet

item Code :- ETIJ-21

Edutek Instrumentation are offering a wide reange of Impact Of A Jet.

DESCRIPTION :- The Impact Of A Jet setup consists of a two sided clear fabrication section. Water is fed through a nozzle and discharged vertically to strike a target carried on a stem which extends through the cover. A weight carrier is mounted on the upper end of the stem. The dead weight of the moving parts is counter balanced by a compression spring. The vertical force exerted on the target plate is measured by adding the weights supplied to the weight pan until the mark on the weight pan corresponds with the level gauge. A total of two targets are provided, a flat plate and a hemispherical cup.

EXPERIMENTATION - To measure the force developed by a jet of water impinging upon a stationary object and comparison with the forces predicted by the momentum theory.

Product Details:

Gear Pump Demonstration Unit

Model No : ETFM-1

Edutek Instrumentation are Manufacturer, Exporter & Supplier of Gear Pump Demonstration Unit.The setup is designed to study the performance of Gear Pump.Set up consists of a gear pump having a pair of meshed gears coupled with electrical motor, supply tank, measuring tank & pipe fittings for closed loop oil circulation. Pressure and Vacuum gauges are connected on delivery and suction side of pump for the purpose of measurement.The flow rate of water is measured using measuring tank and stop watch provided.

Experiments :

• To determine overall efficiency and pump efficiency of the gear pump.
• To plot Head vs. Discharge, Pump efficiency vs. Discharge

Features of Gear Pump Demonstration Unit :

• Closed loop circulation.
• Compact & stand alone set up.
• Stainless Steel tanks and wetted parts.
• Superb Painted structure.
• Simple to operate & maintain.

Product Details:

Pressure Drop Through Packed Bed

Model No : ETPT-66

Under the supervision of our skilled technocrats, these machines are manufactured as per the latest technological advancements utilizing quality approved raw materials. Offered product is acknowledged for its robust construction, low maintenance, longer functional life and energy efficiency. We offer pressure drop in both, standard and customized specifications to our valuable clients.

Features:

• Highly efficient.
• Premium quality.
• Durable finish.

Specifications:

• Packed Column Material Borosilicate Glass with both end made of Stainless Steel.
• Packing Material Borosilicate Glass rings, Size 8-10mm approx.
• Water tank Material Stainless Steel, Capacity 30 Ltrs.
• Water Circulation FHP Pump Crompton/Sharp make.
• Flow Measurement Rotameters for water.
• Drop Measurement Manometer.
• The whole set-up is well designed and arranged in a good quality painted structure.

Additional Information:

• Item Code: ETPT-66
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Losses Due To Friction In Pipe Line

model no : ETLF-53

We offer highly demanded Losses due to friction in pipe line at the most competitive market price. Manufactured in accordance with the industry laid parameters, offered apparatus is highly demanded around the globe. The setup is designed to study the losses due to friction in pipes of different diameters and materials. This consists of a set of 3 different pipe test sections, supply tank, measuring tank and pump for closed loop water circulation.

Experiments:

• To determine the losses due to fiction in pipes.

Utilities Required:

• Electric supply 0.5 kW, 220V AC, Single Phase.
• Water supply Tap water connection ” BSP Distilled water @ 60 liters (optional).
• Floor Area with Drain facility.

Technical Specifications:

• Pipes (2 Nos.): Material GI of ½” & 1” diameter.
• Pipe Test Section Length: 1 m.
• Instruction Manual: An ENGLISH instruction manual will be provided along with the Apparatus.

Additional Information:

• Item Code: ETLF-53
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Cavitation Demonstration Unit ETFM-4

We Are Engaged In Manufacturing Supplying And Exporting The Best Quality Of Cavitation Demonstration Unit. By Using Advanced Technology Being Customer Centric Brand, We Are Manufacturing And Supplying Supreme Quality Cavitation Demonstration Unit For Our Esteemed Customers. This Cavitation Demonstration Unit Is Processed Using High Quality Raw Material Which Ensures Its Standard Quality And Long Service Life. Our Presented Product Passes Through Diverse Quality Parameters For Inspection. Moreover, It Can Be Availed From Us At Reasonable Costs.

Description - The Apparatus Has Been Designed To Demonstrate The Phenomena Of Cavitation. The Present Set-Up Consists Of A Test Section Made Of Acrylic Having Conversion And Diversion Section. Pressure Tapings At Appropriate Position Are Provided. This Test Section Is Having One Control Valve At Upstream Side To Regulate The Water Flow Rate. Two Pressure Gauges Are Connected To These Taping Which Give The Pressure Readout At The Time Of Flow Passing Through This Test Section. The Unit Is Self-Contained Close Circuit Type With Sump Tank, Measuring Tank And Centrifugal Pump. Flow Through Test Section Can Be Regulated With The Help Provided By-Pass And Control Valve.

Experimentation

• To Observe The Phenomena Of Cavitation.
• To Compare The Theoretical And Actual Pressures At Cavitation Condition.

Features Of Cavitation Demonstration Unit

• High Load Bearing Capacity.
• Compact Design.
• High Performance.

Additional Information:

• Item Code: ETFM-4
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Aerodynamics Trainer ETFM-9

We offer high quality Aerodynamics Laboratory Trainers for study of basic as well as advanced principles of Aerodynamic Engineering. Our product range include Modular Air Flow Bench for study of basic principles of Aerodynamics & Subsonic Wind Tunnel for analysis of advanced principles of Aerodynamics. Wide range of experimental modules are available for determination of Drag & Lift Force, Pressure Distribution on Aerofoils, Boundry Layer Analysis, Flow Visualization etc.
velocity measurement of flows with Pitot tube

- boundary layer analysis on a flat plate with flow

along the plate

- drag of bodies

- demonstration of the Coanda effect

- visualisation of streamlines

together with appropriate accessories: experiments from the field of steady incompressible flow

- velocity measurement of flows with Pitot tube and

Pitotstatic tube

- free jets

- flow in a pipe elbow

- proof of Bernoulli's principle

Features :

• Flow velocities up to 40m/s possible1
• Homogeneous flow through the flow straightener

and special nozzle contour1

• Matching accessories offer a wide range of experiments

Technical Data :

Radial fan

- power consumption: 0,37kW

- max. flow rate: 15m³/min

- nozzle exit cross-section: 50x100mm
- max. flow velocity at the nozzle exit: 40m/s.

Additional Information:

• Item Code: ETFM-9
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Energy Losses in Bend c

• This Energy Losses in Bends and Fittings Model has been designed for students experiment on the investigation of energy losses in pipe bends and fittings including valves.

• The equipment is mounted on a free-standing framework supporting the test pipe work and instrumentation.

Additional Information:

• Item Code: ETFM-6
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Item code: ET-244

Kaplan Turbine Test Rig (1 KW capacity 5HP supply pump)

a) Test rig consists of a Kaplan turbine designed for laboratory experimental purposes and to conduct test in metric units. The specifications of the turbine are as follows:

Normal Speed - 2200 RPM.

Capacity - 1.0 KW

The unit consists of a cast iron casing, a rotor assembly of shaft, an axial flow gunmetal runner and a brake drum all mounted on a suitable sturdy base. The runner has vanes of aerofoil section. Fixed guide vanes are provided in the turbine to regulate the flow into the runner. A conical draught tube is connected to the turbine outlet by a bend. For observing the flow at the runner exit a transparent window made of thick Perspex tube is provided in between the turbine casing and the draft bend. A rope brake arrangement with a set of dead weights and spring balance is provided for loading the turbine. Pressure gauge and vacuum gauge are fixed at the inlet and outlet to measure the net supply head to the turbine.

b) Water to the turbine is provided by a centrifugal pump set of 5HP capacity. The pump operates on 440Volts, 3 Phase, 50 Hz line.

c) Other standard accessories include a DOL starter, switch, flow control valve, suitable piping.

d) Flow measuring unit consists of a venturimeter with pressure taps connected to two pressure gauges mounted on a panel board.

e) The complete test rig is mounted on a storage tank of suitable capacity. The tank is provided with FRP lining for total rust protection

 

Additional Information:

• Item Code: ET-244
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer)

Product Details:

Francis Turbine Test Rig (1 KW capacity)

Item code: ET-242

a) Test rig consists of a Francis water turbine designed for laboratory experimental purpose and to conduct test in metric units.

The specifications of the turbine are as follows:-
Normal Speed - 2200 RPM.
Capacity - 1.0 KW
The unit consists of a cast iron casing, a rotor assembly of shaft, gunmetal runner and a brake drum all mounted on a suitable sturdy base. Guide vanes are provided in the turbine to regulate the flow into the runner. A conical draught tube is connected to the turbine outlet by a bend. A rope brake arrangement with a spring balance is provided for loading the turbine. Pressure gauge and vacuum gauge are fixed at the inlet and outlet to measure the net supply head to the turbine.
b) Water to the turbine is provided by a centrifugal pump set of 5 HP capacity. The pump operates on 440Volts, 3 Phase, 50 Hz line.
c) Other standard accessories include a DOL starter, switch, flow control valve, suitable piping.
d) Flow measuring unit consists of a venturimeter with pressure taps connected to two pressure gauges mounted on a panel board.
e) The complete test rig is mounted on a storage tank of 500 liters capacity. The tank is provided with FRP lining for total rust protection

 

Optional: Electrical loading for 1KW Hydraulic turbines (Francis and Kaplan):

Additional Information:

• Item Code: ET-242
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Francis Turbine Test Rig (5HP output 15HP supply pump)

Item code: ET-243

a) Test rig consists of a Francis water turbine designed for laboratory experimental purpose and to conduct test in metric units. The specifications of the turbine are as follows: -
Design Speed - 1500 RPM.
Capacity - 3.7 KW. (5.0 HP)
Design Head - 15-20m and 1800-2000 lpm.
The unit consists of a cast iron spiral casing, a bearing pedestal, a rotor assembly of shaft, gunmetal runner and brake drum all mounted on a suitable sturdy base. Aerofoil shaped gunmetal guide vanes are provided in the turbine to regulate the flow into the runner. The guide vane opening adjustment is made through a hand wheel and a suitable link mechanism. A conical draught tube is connected to the turbine outlet by a bend. For observing the flow at the runner exit, a transparent window made of thick perspex tube is provided in between the turbine casing and the draft bend. A rope brake arrangement with a set of dead weights and spring balance is provided for loading the turbine. Pressure gauge and vacuum gauge are fixed at the inlet and outlet to measure the net supply head to the turbine.
b) Water to the turbine is provided by a centrifugal pump set of 15 HP capacity. The pump operates on 440Volts, 3 Phase, 50 Hz line.
c) Other standard accessories include a star-delta starter, switch, flow control valve, suitable piping.
d) Flow measuring unit consists of a venturimeter of size 100mm with pressure taps connected to two pressure gauges mounted on a panel board.

e) The complete test rig is mounted on a storage tank of sutiable capacity. The tank is provided with FRP lining for total rust protection

Additional Information:

• Item Code: ET-243
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Item code: ET-245

Multistage centrifugal pump test rig  :

a) The test rig consists of a 2-stage centrifugal pump set suitable for determining its characteristics at its rated speed. The test centrifugal pump is of 1.0 HP capacity of size
25mmx25mm(1"x1"). The pump is powered by 220 volts, single phase, 50Hz. A stop watch and an M.S. collecting tank of size 150 liters. with a gauge glass scale fitting, a drain valve and a bend are provided to measure the actual flow rate. An energy meter is provided to measure the input power to the pump set.

b) Other standard accessories include switch, flow control gate valve, foot valve and piping system with suitable pressure taps to fix the pressure and vacuum gauges.

c) A sump tank of size 250 liters with suitable drain is provided to store the water. A strong iron stand fitted with wheels supports the complete test rig. The unit is moveable.
All tanks are provided with FRP lining for total rust protection.

Additional Information:

• Item Code: ET-245

Product Details:

Series and Parallel Pumps
Item code: EDSP-11

Edutek are offering a wide range of Series And Parallel Pump Demonstration Unit.
Features of Series and Parallel Pumps Demonstration Unit
Investigation and operating behaviour of pumps in various operating modes single pump, series or parallel pump operation, configurable via valves closed water circuit contains centrifugal pumps with drive motor and a transparent water tank.one pump with variable speed and one pump with fixed speed adjustment of flow resistance by a valve in the delivery pipesensors for pressure on intake and delivery sides of the pumps and flow rate microprocessor-based measuring technique.

Additional Information:

• Item Code: EDSP-11
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Pelton Turbine

Item code: EDPT-13

We are able to offer a wide range of Pelton Wheel Test Rig. It is manufactured using high grade raw material and innovative technology in compliance with globally accepted norms of quality. The offered range is widely acclaimed in the market, owing to its specific attributes like high efficiency and fine finishing. Our Clients can avail the pelton wheel test rig from us within stipulated time period.

Features :

• Easy to functionality.
• Sturdy construction.
• Negligible maintenance.

Other Descriptions :
The unit is designed to show students how an impulse turbine works and test its performance.
The turbine power is adjusted by means of the nozzle cross-sectionThe experimental unit consists of the Pelton wheel, a needle nozzle used as control device (control flow rate), a rope brake dynamometer for loading the turbine and a housing with a transparent front panel.
The transparent cover enables you to observe the water flow, the wheel movement during operationThe pressure at the turbine inlet is recorded with a pressure gauge
A spring balance to measure brake power and a digital RPM indicator are attached to wheel shaft Thus, the mechanical power output of the turbine can be determined.
Flow rate measurement are provided by orifice meter.

Additional Information:

• Item Code: EDPT-13
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Axial Flow Impulse Turbine Demonstration

Item code: EDAF-12

Product Specification Axial-Flow Impulse Turbine : 

Axial flow impeller turbine demonstration model, designed for use in conjunction with the Turbine Service Unit. The turbine unit is placed on the Turbine Service Unit and supplied with water by the service unit. The turbine housing is made of Plexiglass so that the axial water jet can be clearly observed. A braking device is fitted to the impeller shaft of the turbine. The braking device is in the form of a band brake. The load and moment on the turbine shaft is measured with a strain gauge fitted
to the braking device. An inductive proximity switch measures the rotational speed of the turbine.

Specification :

1. Axial flow impeller turbine demonstration model.
2. Electronic measurement of the moment on the turbine shaft using a band brake.
3. Electronic measurement of the turbine rotational speed with inductive proximity switch.
4. Transparent turbine housing.

 

 

Additional Information:

• Item Code: EDAF-12

Product Details:

Orifice Discharge Apparatus

We are offering a wide range of fluid Mechanic lab equipment for engineering colleges. Our company offers optimum quality Orifice Discharge Apparatus at the most reasonable market price. This apparatus is manufactured under the supervision of expert professionals, using best quality raw materials. The apparatus manufactured by us is used for the purpose of measuring fluid flowing through an open channel. Offered apparatus is exclusively demanded in various hydraulic industries for accurate performance and hassle-free installation. In addition to the sharp edged orifice, four additional orifices with different profiled are supplied. The Orifice Discharge accessory consists of a cylindrical Clear acrylic tank which has an orifice fitted in the base. A traverse assembly is provided which enables a pitot tube to be positioned anywhere in the jet. Attached to this pitot tube is a fine wire which can be traversed across the jet to accurately measure the jet diameter and the vena contracta diameter and so determine the contraction coefficient.

Specifications of Orifice Discharge Apparatus :

• Determining the contraction and velocity coefficients.
• Calculating the discharge coefficient.
• Cylindrical glass tank with orifice fitted in base.
• Four interchangeable orifices.
• Pitot tube and knife edge to measure jet velocity and diameter.
• Establishing the coefficient of velocity for a small orifice.

Additional Information:

• Item Code: ETOD-14
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Plunger Pump Demonstration Unit

Model No : EDTP-15

We are offering a wide range of fluid Mechanic lab equipment for engineering colleges. Our company offers optimum quality plunger pump demonstration unit at the most reasonable market price. This apparatus is manufactured under the supervision of expert professionals, using best quality raw materials. The apparatus manufactured by us is used for the purpose of measuring fluid flowing through an open channel. Offered apparatus is exclusively demanded in various hydraulic industries for accurate performance and hassle-free installation.

Specification of Plunger Pump Demonstration Unit
Small scale plunger pump demonstration unit. Capable of being linked to a not supplied via an interface console an essential accessory. Supplied with software providing full instructions for setting up, operating, calibrating and performing the teaching exercises. Facilities provided for logging, processing and displaying data graphically.

Additional Information:

• Item Code: ETPD-15
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Flow Through Non Circular Pipe

Model No : ETFTN-57

We have garnered praise of manufacturing highly qualitative Flow Through Non Circular Pipe.These are manufactured using quality-approved raw materials in accordance with industrial norms and guidelines. These are used in civil engineering laboratories for applications that involve friction between fluids of different kinds. Easy to set up and install, these are made available to clients at reasonable prices. These are supplied to clients in different specifications at affordable prices.

Friction head losses in straight pipes of different sizes can be investigated over a range of Reynolds' numbers from 103 to nearly 105, thereby covering the laminar, transitional and turbulent flow regimes in smooth pipes. A further test pipe is artificially roughened and, at the higher Reynolds' numbers, shows a clear departure from typical smooth bore pipe characteristics.

In addition to the smooth and roughened pipes, a wide range of pipeline components are fitted, including pipe fittings and control valves, allowing investigation of the losses caused by this type of connection. A clear acrylic section of pipeline houses a Venturi meter, an orifice plate assembly and a Pitot tube, so that these can be investigated as flow measurement devices.

Features:

• Excellent quality.
• Easy to install.
• Reasonably priced.

Additional Information:

• Item Code: ETFTN-57
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Computerized Venturi Meter

Model No : ETFM-2

Computerized Venturi Meter Our hardworking teams help us engage in the manufacture of highly qualitative Computerized Venturi Meter. These are made using quality-approved raw materials in compliance with industrial guidelines. These are rigorously tested by our team of well-qualified quality analysts for efficiency. These are widely used apparatus in the civil engineering industry and are highly acclaimed for being sturdy and durable. These are also exported overseas in order to facilitate easy access by clients based abroad. These are priced economically.

Features: Reasonably priced Quality-tested Sturdy design

Additional Information:

• Item Code: ETFM-2
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Flow Through Circular Pipe

Model No : ETFTC-56

We have garnered praise of manufacturing highly qualitative Flow Through Circular Pipe. These are manufactured using quality-approved raw materials in accordance with industrial norms and guidelines. These are used in civil engineering laboratories for applications that involve friction between fluids of different kinds. Easy to set up and install, these are made available to clients at reasonable prices. These are supplied to clients in different specifications at affordable prices.

Features:

• Excellent quality.
• Easy to install.
• Reasonably priced.

Additional Information:

• Item Code: ETFTC-56
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Impact Of Jet Apparatus c

We are counted among the most prominent manufacturers, traders and exporters of high quality Impact of jet of vanes. Designed in compliance with industry leading parameters, it is used to study the forced developed of a jet of water on different surfaces and to compare it with momentum theory. Offered set up consists of visible test enclosure, supply tank, measuring tank and pump for closed loop water circulation.

Description:

• The setup consists of a two sided clear fabrication section. Water is fed through a nozzle and discharged vertically to strike a target carried on a stem which extends through the cover. A weight carrier is mounted on the upper end of the stem. The dead weight of the moving parts is counter balanced by a compression spring. The vertical force exerted on the target plate is measured by adding the weights supplied to the weight pan until the mark on the weight pan corresponds with the level gauge. A total of two targets are provided, a flat plate and a hemispherical cup.

Experimentation:

• To measure the force developed by a jet of water impinging upon a stationary object and comparison with the forces predicted by the momentum theory

Utilities required:

• Hydraulic Bench

TechnicaL Specifications:

• Test Plates: Material Brass (2 Nos.), Flat Plate, Hemispherical Cup.
• Nozzle: Material Brass.
• Stainless Steel enclosure: Having of opposite sides made of glass.
• Instruction Manual: An ENGLISH instruction manual will be provided along with the Apparatus.

Additional Information:

• Item Code: ETIJA-52
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Free Forced Convection System ETFCS-61

Free Forced Convection System It is because of the vast domain knowledge and astute expert guidance, we have been able to bring forth a broad gamut of Heat Transfer in Forced Convection Apparatus that are designed with utmost precision. Followed by our manufacturing process, these apparatuses are checked in order to ensure a range that is free from flaws and are capable to offer maximum performance at the clients' end.

Some feature are:

• Highly durable.
• Reliable performance.
• Has sturdy design.
• Quality approved.

Specification:

Electricity Supply: 1 Phase, 220 V AC, 10 AmpFloor area of 1.2 m x 0.5 mDia: 28 mmLength: 400 mm.

Additional Information:

• Item Code: ETFCS-61
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Bernoulli's Apparatus ET-243B

Our organization is counted among the listed manufacturers, wholesalers and exporters of premium quality Bernoulli’s apparatus. Offered apparatus is precisely manufactured under strict supervision in compliance with industry laid parameters. These units consist of a rectangular transparent flow section through which water is to be flown. The velocity of water changes across the sectional area of channel changes.

Experiments:

• To verify Bernoulli's Theorem experimentally
Utilities Required:
• Electric supply 0.5 kW, 220V AC, Single Phase.
• Water supply Tap water connection ” BSP Distilled water @ 60 liters (optional)
• Floor Area with Drain facility ..

Technical Specifications:

• Electric supply: 0.5 kW, 220V AC, Single Phase.
• Inlet Tank Capacity: 20 Ltrs. MOC SS.
• Supply Tank Capacity: 85 Ltrs. MOC SS.
• Measuring Tank Capacity: 40 Ltrs. MOC SS fitted with Piezometer Tube & scale.
• Piezometer Tubes: Material P.U. Tubes (9 Nos.).

Additional Information:

• Item Code: ET-243B
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Flow Over A Notch ETFM-5

The notch or weir is fitted, water supply is given at one end of channel. Water flow over notch or weir. Arrangement are made to measure the still level to determine the head.

Features:

Interchangeable Brass/Aluminum notches.
Measurement of head by scale.

Range Of Experiments:

To determine coefficient of discharge through.
60° 'V' notch.
Rectangular notch.

Specifications:

Water storage tank.
Notches 60 included angle 'V' notch.
Rectangular notch.
Notch interchanges arrangement.
Measuring tank & collecting tank & stop watch.

Service Required:

Water supply.
Suitable floor space of 2 m. x 2 m.

Additional Information:

• Item Code: ETFM-5
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Losses In Piping Systems ETFM-7

We are considered in the market to be one of the leading manufacturers and suppliers of this Losses In Piping Systems. For the purpose of maintaining this reputation, we indulge in the use of the best quality raw materials that are available. Manufactured in compliance with the set industrial norms, the offered product is one of the best that is available in the market. The offered apparatus is used widely for the purpose of measuring the rate of friction.

Specification

• Demo panel for investigating the pressure losses in pipes.
• Demo panel on laboratory trolley.
• 10 different pipe sections for experiments.
• Pipe section selection using hose connections with rapid action hose couplings.
• Standard measuring length of 1000mm for pipe friction measurements.
• Manometer panel 300mmWG.
• Double manometer 850mmWG.
• Differential pressure measuring unit 0..2000mbar, battery operated.
• Flow rate measurement with variable-area flowmeter 1600ltr/h.

Additional Information:

• Item Code: ETFM-7
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Basic Hydraulic Bench

Model No : -ETFM10

The Basic Hydraulic Bench is of volumetric type and has been designed to provide continuous and controlled supply of water to conduct various experiments using auxiliary modules in typical Fluid Mechanics and Hydraulics Laboratory. The unit is an ideal service unit for conducting student projects. Once filled, no external water supply is required. Water is recycled between the Experiment Module, Measuring Tank and the Storage Tank by the Centrifugal Pump.

Several experiments in Fluid Mechanics and Hydraulics require continuous and controlled supply of water. The Basic Hydraulic Bench provides a controlled recirculation water supply to conduct experiments.

The Basic Hydraulic Bench is a very important module and is recommended for all Fluid Mechanics and Hydraulics Laboratories in Educational Institutions. It is a basic module for flow related experiments using auxiliary modules.

A list of common experiments that can be conducted using the Basic Hydraulic Bench is given below:
1. Impact of a Jet.
2. Flow over Weirs.
3. Bernoulli’s Theorem Demonstration.
4. Orifice Discharge.
5. Energy Loss in Bends.
6. Osborne Reynolds Demonstration.
7. Energy Loss in Pipes.
8. Hydrostatic Pressure.
9. Flow Visualization in Channels.
10. Dead Weight Calibrator.
11. Metacentric Height.
12. Series & Parallel Pumps.
13. Centrifugal Pump Characteristics.
14. Free and Forced Vortices.
15. Water Hammer.
16. Pelton Turbine.
17. Orifice & Free Jet Flow.
18. Flow Meter Demonstration.
19. Cavitations Phenomenon Demonstration.
20. Laminar Flow Demonstration.
21. Radial Flow Turbine.
22. Venturi, Bernouli and Cavitation.
23. Pipe Friction Apparatus.
24. Equipment for the Study of Porous Beds in Venturi Tubes.
25. Flow Channel 1m Length.
26. Depression Measurement System (Vacuum Gauge).
27. Axial Flow Turbine.
28. Pump Impeller Display Panel.

Additional Information:

• Item Code: ETFM10
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Item code: 11967

Thiscomputerised pressure measurment bench(Model: 11967) is a complete laboratory bench for test and calibration of the various elements of pressure readings as defined by new specifications for the industry. The unit is also an excellent test bench for all other disciplines which involve measuring and generatingpressure. All pressure gauges are supplied with easy-to-read dial scales so that students are able to compare figures from documented records with how the pressure gauges are constructed in reality.

Additional Information:

• Item Code: 11967

Product Details:

Reynolds Apparatus ETRA-59

Reynold’s Apparatus Complete with Collecting Tank: We are among the trusted names engaged in the manufacturing, trading and exporting of best quality Reynolds Apparatus. The set-up we offer is basically a self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Our professionals manufacture this apparatus in accordance with the industry set parameters using best quality raw materials. This apparatus is used to measure flow rate and is available at affordable market prices.

Experiments:

To determine the Reynold's number and hence the type of flow either laminar or turbulent

Technical Specifications:

Tube: Material Borosilicate Glass Dye vessel: Material Stainless Steel, Suitable Capacity Capillary Tube: Material Copper/Stainless Steel Constant Head Water Tank: Capacity 40 Ltrs Water Circulation: FHP Pump, Champion/ godrej make Flow Measurement: Using Measuring Cylinder Sump Tank Capacity: 60 Ltrs Stop Watch: Electronic Control Panel Comprises of: Standard make On/Off Switch, Mains Etc Instruction Manual: An ENGLISH instruction manual will be Provided along with the Apparatus Tank Material: Stainless Steel

Additional Information:

• Item Code: ETRA-59
• Pay Mode Terms: T/T (Bank Transfer)